Ricoh FV-L500B1 User Manual

1/31 FV-L500B1 User’s Guide Rev. 1.02 Small Cubic Type 5.0 Mega Pixel CCD Monochrome PoCL Camera Link Camera FV-L500B1 User’s Guide

10/31 FV-L500B1 User’s Guide Rev. 1.02 2.2 Binning Mode (Setting 10H: 1XX1XXXX) 2.2.1 Horizontal Timing 1 CLK = 15.625 ns

11/31 FV-L500B1 User’s Guide Rev. 1.02 2.2.2 Vertical Timing 2.2.2.1 Binning Full Scanning (Setting 10H: 1XX10XXX, 11H: XXX0X000) 1 H = 3

12/31 FV-L500B1 User’s Guide Rev. 1.02 2.2.2.3 Binning 1/2 Partial Scanning (Setting 10H: 1XX11XXX, 11H: XXX0X001) 1 H = 30.063 μs, 54

13/31 FV-L500B1 User’s Guide Rev. 1.02 2.3 Data Order on the Camera Link Output DA0 to DA11: 12bit data for one pixel from the f

14/31 FV-L500B1 User’s Guide Rev. 1.02 2.4 2 Taps Transferring Image (2XE-1Y） XWYHXW-1YHX2YHX1YHTap1Sep X = 1Sep Y = 1X1YH-1X2YH-1XWYH-1XW-1Y

15/31 FV-L500B1 User’s Guide Rev. 1.02 3 Camera Operational Mode 3.1 Normal Mode In this mode, the images are output continuously. 3.1.1

16/31 FV-L500B1 User’s Guide Rev. 1.02 3.2 Pulse Width Trigger Mode In this “pulse width trigger mode” with positive polarity, the came

17/31 FV-L500B1 User’s Guide Rev. 1.02 3.2.2 Pulse Width Trigger Mode (Non-Reset) Note 1: The camera does NOT switch to n

18/31 FV-L500B1 User’s Guide Rev. 1.02 3.3 Edge Preset Trigger Mode In this “edge preset trigger mode”, the camera exposure starts at the ris

19/31 FV-L500B1 User’s Guide Rev. 1.02 3.3.2 Edge Preset Trigger Mode (Non-Reset) Note 1: The camera does NOT switch to no

2/31 FV-L500B1 User’s Guide Rev. 1.02 Table of Contents 1 Connector Specifications...

20/31 FV-L500B1 User’s Guide Rev. 1.02 3.4 H Reset Mode Normally, video noise appears when the beginning of trigger signal is applied before

21/31 FV-L500B1 User’s Guide Rev. 1.02 4 Communication Protocol This camera has a communication function that enables external devises, such

22/31 FV-L500B1 User’s Guide Rev. 1.02 The description of the format is as follows. Name Descriptions SOF Start of Frame. Always set or rec

23/31 FV-L500B1 User’s Guide Rev. 1.02 【Example Code】Reading the data from the command 00H  Command to send: 02H, 00H, 00H, 01H, 00H, 03H

24/31 FV-L500B1 User’s Guide Rev. 1.02 4.4 Camera Control Command 4.4.1 Camera Command List  The data unit of the each command is 1 byte

25/31 FV-L500B1 User’s Guide Rev. 1.02 81 to EFH Reserved - - Command No. R/W Save to EEPROM Function Initial Data Data Range F0H R/W

26/31 FV-L500B1 User’s Guide Rev. 1.02 4.4.2 Descriptions of the Camera Control Commands (The underline settings are the factory default set

27/31 FV-L500B1 User’s Guide Rev. 1.02 Command No. Command Descriptions 14H: UART[70] [Communication mode] Initial Data: 01H This sets the co

28/31 FV-L500B1 User’s Guide Rev. 1.02 Command No. Command Descriptions 26H: PWR[70] 27H: PWR[158] [Effective line numbers in the variable

29/31 FV-L500B1 User’s Guide Rev. 1.02 Command No. Command Descriptions 68H: DIGITAL_ CLAMP[70] [Digital clamp] Initial data: DIGITAL_CLAMP

3/31 FV-L500B1 User’s Guide Rev. 1.02 1 Connector Specifications 1.1 Camera Link Connector SDR (3M) or equivalent This produc

30/31 FV-L500B1 User’s Guide Rev. 1.02 Command No. Command Descriptions 79H: EFFCT[70] [Image effect selection] Initial data: EFFCT[7..0]

31/31 FV-L500B1 User’s Guide Rev. 1.02 5 Revision History Rev Date Changes Note 1.00 2012/06/15 Initial Release 1.01 2012/07/13 Updat

4/31 FV-L500B1 User’s Guide Rev. 1.02 1.2 Power-I/O Connector  HR10A-7R-6PB（Hirose）or equivalent  This connector is for the power supply

5/31 FV-L500B1 User’s Guide Rev. 1.02 1.3 Equivalent Circuit for the Input Pin of the I/O Connector +3.3V +3.3VTC7WH241FKTOSHIBATRIGGER IN1

6/31 FV-L500B1 User’s Guide Rev. 1.02 2 Camera Output Timing Charts 2.1 Normal Mode (Setting 10H: 1XX0XXXX) 2.1.1 Horizontal Timing 1

7/31 FV-L500B1 User’s Guide Rev. 1.02 2.1.2 Vertical Timing 2.1.2.1 Normal Full Scanning (Setting 10H: 1XX00XXX, 11H: XXX0X000) 1 H =

8/31 FV-L500B1 User’s Guide Rev. 1.02 2.1.2.3 1/2 Partial Scanning (Setting 10H: 1XX01XXX, 11H: XXX0X001) 1 H = 30.063 μs, 32.015 Hz

9/31 FV-L500B1 User’s Guide Rev. 1.02 2.1.2.5 Variable Partial Scanning (Setting 10H: 1XX01XXX, 11H: XXX0X111) Inte