(R1)
22.7
2.3
1/4”20UNC(Screw for Tripod)
φ2.0 Depth 2.5 H7
+0.010
0
4–M4 Depth 4
2.
0
Depth 2.5 H7
+0.010
0
17.69
±0.02
15.5
±0.05
14.5
±0.05
25
±0.05
16.8
±0.05
15
±0.02
35
4-R3
35
φ
36
0
−0.05
40.7
U1(C Mount Screw)
φ
30
17.69 [CCD image area: in air 17.526]
10.5
B
A
Pin No.
Signal
name
IN/
OUT
Voltage
Low voltage High voltage
1 GND IN 0V
2 I/O-1 IN/OUT
IN 0 to +0.99V +2.3 to +3.3V
OUT 0V +3.3V
3 I/O-2 IN/OUT
IN 0 to +0.99V +2.3 to +3.3V
OUT 0V +3.3V
4 I/O-3 IN/OUT
IN 0 to +0.99V +2.3 to +3.3V
OUT 0V +3.3V
5 TRIGGER OUT OUT 0V +3.3V
6 N.C.
A
B
Camera
Link
5 Mega-
pixel
PoCL
FV-L500B1
Camera Link
™
5 Megapixel Camera
[Exposure-interval signal output] outputs the camera exposure interval and enables efficient inspection
[Supported cameras] FV-L500B1, FV-L200B1, FV-L030B1, FV-G200B1,
FV-G030B1
Exposure-interval signal output – which can start the next exposure during the
transfer of the previous image – makes it possible to achieve high-speed work
inspection*, thereby raising inspection efficiency. In addition, since the camera
exposure interval is output externally, it can be used for various purposes.
*
Limited to cases where the next exposure does not end before the completion of image transfer.
5M Camera Link with highly rigid case
and compact design
35 mm×35 mm compact design
Uses PoCL (Power over Camera Link), which has a strong track record
as a high-resolution digital camera interface
High-speed frame rate of 5M: 16 fps
Various trigger modes (pulse width, edge preset trigger) as standard features
In addition to camera tripod screw holes, M4 screw holes are located on
four sides (top, bottom, left, right)
To increase mounting precision, mounting holes are arranged based on the
CCD optical axis
Use in tasks such as fault inspection, display inspection, solder defect
inspection, and high-precision flaw detection for semiconductors, liquid
crystal and plasma flat panel displays, circuit boards, etc.
Dimensions and rear connector specifications
Camera Link connector
3M-made SDR equivalent
Input/output signal connector
Hirose-made HR10A-7R-6PB equivalent Trigger signal input can be done in accordance with the
camera setting.Optional connector RICOH FP-CN6PB is supported.
Note: For the frame grabber board and cable, the PoCL type should be used.
FV-L500B1 Product specifications
Imager 2/3" interline 5.0 Mega pixels monochrome progressive CCD
Active picture elements 2448 (H) × 2058 (V)
Cell size 3.45 (H) × 3.45 (V) µm
Vertical frequency
(Frame rate)
16 Hz
Horizontal frequency 33.264 kHz
Pixel frequency 64 MHz
Minimum scene illumination 0.24 lux at F1.2
Sync. System Internal
Video output Digital 8 , 10 or 12 bit Raw Data (Base configuration)
Shutter speed
OFF, 1/8
to
1/209,000 sec. (Variable at every H and clock)
Gain 0 to 18.309 dB
Gamma 1.0
Power supply
Input voltage 12 Vdc ± 10%
Consumption Less than 4.0 W
Dimensions 35 (W) × 35 (H) × 40.7 (D) mm (excluding the connector)
Lens mount C mount
Weight Approximately 80 g
Operational
environment
Operational
temperature
-5 to 40 deg. C
Storage
temperature
-30 to 65 deg. C
Cameras supporting
exposure-interval
signal output
Standard cameras
• Exposure starts during image transfer.
The CCD exposure start marked with the is speeded up, thereby making high-speed work detection possible.
CCD exposure
Trigger signal
Camera image
output
CCD exposure
Trigger signal
Camera image
output
(Unit: mm)
03
(48 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals